Dab of hot glue on each one to keep it stuck down.
this post was submitted on 27 Nov 2024
41 points (97.7% liked)
Hardware Gore
614 readers
83 users here now
Welcome to /c/HardwareGore!
This community is dedicated to showcasing broken hardware like phones, laptops, computer hardware and other devices. Here, you can see everything from shattered screens, bent casings, fried motherboards, destroyed gadgets, to liquid damaged phones and battery explosions. Share your unfortunate moments, whether they are unintentional accidents or from moments with lack of control.
Community Rules - Click to expand
These rules are subject to change at any time with or without prior notice. Therefore, you should keep an eye for changes before you make a post or comment.
(last updated: 10th October 2023 - Rewording some rules, minor updates to existing rules and introduction of Rule 7; no actual change in how the community works than it already does)
- This community is a part of the Lemmy.world instance. You must follow its Code of Conduct (https://mastodon.world/about).
- Please keep all discussions in English. This makes communication and moderation much easier.
- Only post content that's appropriate to this community. Inappropriate posts will be removed.
- NSFW content of any kind is not allowed in this community.
- Do not create duplicate posts or comments. Such duplicated content will be removed. This also includes spamming.
- Do not repost media that has already been posted in the last 30 days. Such reposts will be deleted. Non-original content and reposts from external websites are allowed.
- Absolutely no discussion regarding politics are allowed. There are plenty of other places to voice your opinions, but fights regarding your political opinion is the last thing needed in this community.
- Keep all discussions civil and lighthearted.
- Do not promote harmful activities.
- Don't be a bigot.
- Hate speech, harassment or discrimination based on one's race, ethnicity, gender, sexuality, religion, beliefs or any other identity is strictly disallowed. Everyone is welcome and encouraged to discuss in this community.
- The moderators retain the right to remove any post or comment and ban users/bots that do not necessarily violate these rules if deemed necessary.
- At last, use common sense. If you think you shouldn't say something to a person in real life, then don't say it here.
founded 1 year ago
MODERATORS
Nothing is more permanent than a temporary fix.
Update: to the surprise of no one, the tape has already failed after two hours at room temperature.
Only temporary in the sense that the tape will fail as soon as it starts to warm up from these SSDs and latent heat from other components?
Lol, hopefully temporary in the sense that I only need it to work for a couple of minutes, long enough to boot a test system with the card installed in order to find out if the motherboard for which I can't locate a manual supports PCIe bifurcation. If the board recognizes all the drives then I'll shut it down and properly install 4 full-length (2280) Samsung drives which I have yet to order.
Even when they do give the manual they rarely state and sonetimes randomy change between bios updates... Did it work? I need to know!
What is it
smol SSDs instead of long SSDs. The proper fix would be one of these to elongate it
Or if OP has a 3d printer, one of these
Looks like a RAID card with NVME drives held down with electrical tape instead of the screws.
Back in the day I had a RAID controller with a GPU fan taped into it so I get it. The tape stayed there for 6 years. Hopefully OP takes care of it sooner because old electrical tape in a hot environment is absolutely disgusting to clean off
My question would be, how should it be normally? Is it not compatible with that short nvmes? or does it need an adapter?
I tried to find this exactly model and found a dozen similar ones that I'm inclined to think are from the same factory BUT all the ones I saw had the holes drilled for the different length NVMEs. So I'm guessing it's a no-name brand that cut corners
OP could likely drill their own holes assuming they have the right bit. I can't see the back of the card but it's almost definitely blank
Yeah the holes are drawn onto the board but not drilled. Probably to cut corners for few microbucks savings.
Looks like holding 4 SSDs in place with a strip of tape instead of mounting screws
Looks like a need for double sided tape and a 3d printed adapter. Stick the cards down and then use the printed part to hold them down.
I'm not sure if I 3D print so many adapters because it's a useful, easy, quick solution or if I'm just justifying my 3D printers...
