3D Printing

4371 readers

1 users here now

For everyhting 3D printing related.

Please be excellent to each other :)

Icon by Freepik, Banner photo by Thiago Medeiros Araujo

founded 4 years ago

MODERATORS

3dnudel@lemmy.ml

Installed creality Sprite Extroduer Pro kit, now the nozzle is beyond the bed minimum height (lemmy.ml)

submitted 1 year ago* (last edited 1 year ago) by ReakDuck@lemmy.ml to c/3dprinting@lemmy.ml

8 comments fedilink hide all child comments

Having a Creality Ender 3 Pro. Have upgraded the mainboard to a new Silent mainboard. Installed this Extroduer and also have a glass bed. I also purchased another glass bed to exchange the scratched one.

What should I do about my problem? Is my only solution to buy a CR-Touch Sensor? How does the sensor even work? Will it also scratch it when I am not careful enough or is it user friendly and fully automated?

I don't have any other bed except the glas one for now. Should I rather purchase a flexible sheet for the bed instead of a glas bed?

top 8 comments

sorted by: hot top controversial new old

[–] CmdrShepard@lemmy.one 2 points 1 year ago* (last edited 1 year ago) (1 children)

If i understand correctly, your nozzle is too high still even with your Z at its lowest value? You should be able to follow these steps to adjust it lower (under "I've added a BLTouch, how do I set my Z-Offset"): https://marlin.crc.id.au/forum/t/ender-3-v2-frequently-asked-questions/17#heading--zoffset

[–] ReakDuck@lemmy.ml 1 points 1 year ago (1 children)

I still use Z clickers instead of CR Touch. My lowest low with the clicker/lever makes the Nozzle stop below my bed. I could remove the glas bed to shrink my bed and maybe put a metal sheet on it or purchase a thin plate, but with the glas bed, the lowest Low I can get with all the 4 corners is not low enough for the nozzle to not touch the bed.

[–] CmdrShepard@lemmy.one 1 points 1 year ago

The steps are the same regardless of what you're using for a Z sensor. The only issue I see is if your limit sensor physically won't allow the gantry to move lower due to its mounting position otherwise it's a 'soft limit' set exclusively in the firmware (which the above steps allow you to reconfigure).

[–] scotticus42@lemmy.nz 1 points 1 year ago (1 children)

Sounds to me like your issue is that the new nozzle now sits lower in relation to the old one. And so now your Z 0 puts the new nozzle tip below where your bed sits.

Since your not using a probe then all you'll need to do is move your end stop so it triggers at a higher position, and stops your nozzle from ramming the bed.

Move the endstop up higher and then let us know if that helps.

[–] ReakDuck@lemmy.ml 1 points 1 year ago

It did help. Always had not give the stopper a thought that its not hard mounted.

[–] dack@lemmy.world 1 points 1 year ago (1 children)

You can move the Z end stop switch up. This will make the home (z=0) position higher.

[–] ReakDuck@lemmy.ml 1 points 1 year ago* (last edited 1 year ago) (1 children)

I only use the Printer with my Octoprint Raspberry PI. Do I need a display for this? (My Display/Interface is broken since many years so I shrugged and just continued using Octoprint)

Would this still be usable when I don't have a display and just use it with Octoprint?

[–] CIA_chatbot@lemmy.world 1 points 1 year ago

No, on the left column of the printer there is the physical z switch, just lower your nozzle down as low as it will go and loosen the bolts on the switch and move it up till it just clicks. Since your display is broke your going to have to set the z index in goose. Or spend 30 bucks and buy a new display