Rangelus

joined 1 year ago
[–] Rangelus@lemmy.nz 17 points 1 month ago (3 children)

Jesus fucking christ. What a stupid take.

[–] Rangelus@lemmy.nz 2 points 1 month ago

Yeah, I hear you on that. But my view is, that's how much it cost. Cancelling it won't make it cheaper in the future. Sometimes we just need to bite the bullet and pay for what we need.

It's more like an issue with initial quotes than the actual cost of the thing. The problem is, the public sees a big cost and screams "they're wasting our money!", but that's not really it at all. The government is trying to invest in needed infrastructure that benefits all of us in the future. Literally their job.

[–] Rangelus@lemmy.nz 2 points 1 month ago (2 children)

Mate, the infrastructure is reaching end of life anyway and needs replacing.

The benefit of doing it all at once is they were enlarging both terminals to allow better offloading of freight. Pay more now to spend less later.

[–] Rangelus@lemmy.nz 4 points 1 month ago (1 children)

The dumbest thing about changing teacher only days, is they are not counted in then mandatory number of days a school is open for. All this change will do is make them close earlier, so the kids will still be off school and parents will still need to make arrangements.

It's fucking stupid.

[–] Rangelus@lemmy.nz 2 points 2 months ago (1 children)

I must be confusing it with Auckland's recently cancelled project, I remember a bunch of money being spent to purchase land.

I mean, I wish they'd build shit. Total agreement here. It needs to be done, just do it!

[–] Rangelus@lemmy.nz 2 points 2 months ago (3 children)

Oh absolutely, sunk cost fallacy is a problem. No disagreement there.

However, my point is cancelling a project doesn't remove the need. We need better public transport, we need ferries, we need infrastructure upgrades. All of these things need to happen, and the longer they are put off usually the more they will cost. So it's not so simple as a sunk cost, as cancelling a project then doing it again later may very well end up costing more in the long run than the over run cost of the initial project. Case in point, the ferries.

I will admit, though, I know less about the wellington light rail project. I was under the impression that a lot of the cost being spent was paying for land that was needed for the project, but you can probably inform me more about this. I'll just say, rail is still needed (or some form of mass transit system).

[–] Rangelus@lemmy.nz 2 points 2 months ago (5 children)

Infrastructure is expensive, and often goes over budget. It is hard to deliver large projects on time and on budget. Any builder will tell you how often a simple house build goes over time and budget.

Crying about incompetency is silly when the alternative seems to be to throw away money that has been spent for no gain. We have lost all the money spent on the ferries, plus a penalty, for no fucking gain at all. All the money spent working on ALR has been flushed down the toilet. It's fucking insanity.

The answer is not throwing away projects because they cost more than anticipated, it is finishing projects and figuring out how to do it better next time. New Zealand has seriously terrible infrastructure problems and they can only be solved with money, and a lot of it.

[–] Rangelus@lemmy.nz 10 points 2 months ago (1 children)

This stuff pisses me off so much.

Educational curricula should be independent of politics. It should be solely based on educational research and achievement statistics, not fucking ideology.

[–] Rangelus@lemmy.nz 2 points 2 months ago* (last edited 2 months ago) (3 children)

Cheers mate. Neat stuff!

I wonder how much force a sail of that size is expected to produce?

[–] Rangelus@lemmy.nz 2 points 5 months ago

It's all good mate! Thanks for the suggestion. When I first started printing I had that exact issue.

[–] Rangelus@lemmy.nz 3 points 5 months ago (2 children)

Hey mate, I keep my filament in a dry cabinet at 5ish% humidity, and I've had the same results with two different filaments in there. I even chucked my filament in a food dehydrator at 40C for 12h with no effect. I'm pretty sure the filament is dry!

[–] Rangelus@lemmy.nz 2 points 5 months ago

I love these! Thanks for sharing!

 

Ok guys, I'm breaking down and posting here to see if anyone has any ideas. I'm greatful for any advice.

I have an upgraded flsun SR. I recently lost my computer (psu issue, waiting for replacement) and I took this opportunity to switch from Cura to Orcaslicer.

Over-all I'm very happy, and getting some good speeds, but I just cannot remove stringing no matter what I try:

  • Retraction from 0-7mm. After about 3mm, no further effect
  • Retraction speed from 30mm/s-50mm/s. No noticable effect
  • Travel speed and acceleration both high (up to 350mm/s and 6000 accel. No effect
  • Temp from 205-215 with no effect
  • Dried filament and different colours, no effect
  • Wipe on retract on and off, up to 2mm wipe distance and 100% retraction. No effect
  • Messed with scarf seams on and off, no effect
  • No effect from layer heights

My setup:

  • Printer - FLSun SR running klipper with a speede pad
  • Filament - Esun PLA+
  • Upgrades - Deported fans, OMG v2 extruder, volcano hotend and high flow cht nozzle
 

Background:

I am running a mostly stock flsun Super Racer, which had been running pretty well on Marlin. I was having a few problems with print quality at high speed, and in an attempt to improve this I bought the flsun Speeder Pad, flashed it with stock klipper, and got it all up and running. So far so good.

I have been trying to get rid of an annoying stringing issue that I never really had on Marlin, and the more I try to remedy it, the worse it's getting.

The image is from my latest retraction tower test after re-calibrating pressure advance and rotation_distance. I'm really not sure where to go from here.

Settings from the above test:

  • Esun PLA+
  • 220C (for maximum flow)
  • 1000mm/s acceleration (low for a delta)
  • 0.1mm z-hop on retract
  • Firmware retract control running in test tower mode, 0mm start, 0.1mm factor
  • Pressure advance of 0.236

Upgrades from stock:

  • Lighter hotend housing
  • Deported fans
  • Fan ducts

Any advice is greatly appreciate!

UPDATE: It was the filament. I grabbed a spool of grey from my drying cabinet, and only later (after much hair pulling!) realized it was the budget filament I'd bought to try. Switched it out to some good quality esun PLA+ and the stringing practically vanished! See image for final stringing test.

Final retraction settings: 3.5mm at 35mm/s.

I would like to thank everyone for their help! Lemmy is always the best place to get advice!

 

Hi guys,

I used the Docker install from here. It was easy to get Automatic1111's web interface up and running, but I'm trying to add new models and I can't figure out how to do it.

I've created a /data/StableDiffusion folder (which didn't exist), and added model files from /data/models, with no effect. I've added them to /data/models/stable-diffusion (which already exists), with no effect. Is there another location where the files are stored? Do I need to do something else to get them to work?

ETA: Discovered I was using the wrong file type (.pth) instead of the correct one (.ckpt). When I tried it with that file type it works perfectly. Thank you everyone for your quick responses and help! Y'all were way faster and more helpful than Reddit!

 

What client, if any, do you guys use on your phone? I've been using Jerboa, but it has its problems so I'm wondering if there's a better option?

view more: next ›