this post was submitted on 07 Jun 2024
526 points (93.3% liked)
Memes @ Reddthat
990 readers
1 users here now
The Memes community. Where Memes matter the most.
We abide by Reddthat's Instance Rules & the Lemmy Code of Conduct. By interacting here you agree to these terms.
Rules
- No NSFW content
- No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
- Be respectful, especially when disagreeing. Everyone should feel welcome here.
- No porn.
- No Ads / Spamming.
founded 1 year ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
It's only faster because your half ass electrical system is only 120V Also the microwave makes the mug to hot to touch
The electric kettle is still faster on 120v
So does an oxy acetylene tourch, what's your point. Leave me with my glowing red hot coffee mug.
Wait how does the microwave go faster when it's also on half the supply voltage?
They use different methods of putting heat into water.
A microwave turns the electricity into RF radiation that is absorbed by the water. To produce that radiation, the input electricity is converted to thousands of volts by a DC power supply. So regardless of whether it's 120 or 230 input voltage, it all gets converted to the same high voltage DC to run the magnetron.
A classic electric kettle works by running the current from the outlet through a resistive heating element. Double voltage means double heat.
Induction heaters use a power supply to reduce the input voltage while increasing amps and frequency to heat metal through inductance. So, similar to a microwave, the voltage of the outlet is largely irrelevant.
Tl;Dr: microwaves and induction heaters change the supplied voltage to function, so they work the same in UK and US; resistive heaters work faster on 230v like the UK uses.
Because resistive heating is inefficient. You need to pump a lot of power through to get a lot of heat. A microwave does not use resistive heating and works on a completely different principle and therefore the amount of power available is much less importance.
Resistive heating is almost perfectly efficient. Where else would the energy go? Using a hot piece of metal to heat water might be slower than using microwave radiation, but that's a different kettle of fish.
Resistive heating inefficient? What is the energy wasted as, if not heat?
don't the coils glow slightly? I guess light would be mostly wasted energy, no?
Yes all the energy goes into being heat but you have to put a lot of energy into the wire before it heats up. Microwaves barely use any energy in fact it takes more power to run the little clock than the microwave itself.
That's insanely untrue. Microwaves are power hogs up to a 1000 watts or more in some cases. The difference is the heat transmission method. The conduction of heat in a kettle is pretty slow because it forces the heat to propagate through water via convection, which is slower, while the radiation of a microwave antenna distributes the energy more evenly and faster. Consumption is mostly on par but energy transfer differs.
So you mean slow, not inefficient.
I think you are complicating things a tad too much. American kitchens have sockets that provide 240V electricity.
Yeah, but not for countertop appliances. Those are all 110/120VAC. Even things as large as a consumer level refrigerator or freezer are almost always 110/120VAC too.
While I have a kettle for water, there are two issues with them for tea.
Insane troll logic
And our stoves get 400V. Don't pretend that your system is superior, it just isn't.
And safety is a non-issue if you don't stick your fingers in the outlets!
Even if you do stick your fingers in the outlets, it's not a problem if you use a good socket
Especially if the entire house is protected by a GFCI.
You still get shocked by 110V, you don't die from 230V.
Okay, so tell me about the pros, please.