iOS keyboards that don't censor "bad words" by Prismo in c/asklemmy@lemmy.world
[-] Prismo@lemmy.world 9 points 2 weeks ago

I added some swear words as contact names, this is one way to get around the fucking censorship

Men over 30, do you think you are becoming grumpier as you are getting older, or on the opposite, becoming more relaxed and laid back? by Prismo in c/askmenover30@lemm.ee
Antivax quacks are continuing to make up fantastical biological mechanisms for COVID-19 vaccine “shedding” by Prismo in c/science@lemmy.world
[-] Prismo@lemmy.world 10 points 2 months ago

Does mean that the unvaccinated anti-vaxers will keep away from the vaccinated??

3
Multiple email signatures (lemmy.world)
submitted 4 months ago by Prismo@lemmy.world to c/ios_community@lemmy.world
0 comments fedilink

I’ve just switched from multiple email accounts to using the 5 custom domains for iCloud. However, now I’ve lost the per email custom signatures. Is there any way to get this back within the iCloud custom domain setup?

Hair probably had an important function at some point in human evolution but now it's mostly cosmetic by Prismo in c/showerthoughts@lemmy.world
[-] Prismo@lemmy.world 60 points 4 months ago

I appreciate the usefulness of my eyebrows to divert rain away from my eyes. I do not appreciate my moustache’s water gathering properties when walking in humid environments.

Do you sit at a desk and keyboard for multiple hours? If yes, please recommend a good chair. by Prismo in c/asklemmy@lemmy.world
[-] Prismo@lemmy.world 9 points 4 months ago

Surprisingly this chair has come out highly in reviews when compared to 4 figure chairs. I have it and can say it is very comfortable. It’s not going to be the best of the best, however if your budget doesn’t stretch to more than mid-3 figures this could be a good alternative.

https://www.ikea.com/gb/en/p/markus-office-chair-vissle-dark-grey-30261152/

https://www.shortlist.com/lists/best-office-chairs-401080

I’ve just turned 40. What advice would you older lemmy users give me? by Prismo in c/asklemmy@lemmy.world
[-] Prismo@lemmy.world 6 points 5 months ago

Nice! Maybe I should post my experiences from turning 40 onwards!

272
I’ve just turned 40. What advice would you older lemmy users give me? (lemmy.world)
submitted 5 months ago by Prismo@lemmy.world to c/asklemmy@lemmy.world
174 comments fedilink
Farewell dear friend... by Prismo in c/cat@lemmy.world
[-] Prismo@lemmy.world 8 points 5 months ago* (last edited 5 months ago)

This is why I try to make every moment special with them and give them the happiest life possible. It doesn’t make it hurt less, but you can know that you made one souls life as perfect as possible and you loved them with all your heart.

Stricken Japanese Moon mission landed on its nose by Prismo in c/space@lemmy.world
[-] Prismo@lemmy.world 24 points 5 months ago

Many a Kerbal has been left in a face down lander on the Mun. Don’t feel bad Japan.

If it works, it works... by Prismo in c/3dprinting@lemmy.world
[-] Prismo@lemmy.world 26 points 8 months ago

This really summarises the passive aggressive level you get to with a 3D printer: “Lift off the bed now you little fucker!”

34
Possible over extrusion, any advice appreciated! (i.imgur.com)
submitted 8 months ago* (last edited 8 months ago) by Prismo@lemmy.world to c/3dprinting@lemmy.world
8 comments fedilink

https://i.imgur.com/yzJg1ne.jpg

https://i.imgur.com/IgVP7Fj.jpg

Any ideas on this new issue only affecting one of my printers, only seems to be on the bottom layers of a base mode print. The layers that are not done as one continuous spiral. Photos are before and after, ignore the banding on the before! (Thats another issue I have fixed)

Can’t figure this one out, driving me mad as I have orders to fulfil

Solved:

So a combination of three changes finally got me back the correct result.

  1. Changed the nozzle for a brand new one, that helped a lot but still had a fee issues.
  2. Remeasured my extrusion amount and recalibrated the e-steps, they had gone quite a way out.
  3. Reduced the temp by 10°C apart from the first layer.
What's a button you hate tapping or clicking accidentally? by Prismo in c/asklemmy@lemmy.world
[-] Prismo@lemmy.world 6 points 8 months ago

I get this on the web interface of my 3D print server. Occasionally come back in a few hours having printed the wrong file…

[Survey] Can you tell which images are AI generated? by Prismo in c/technology@lemmy.world
[-] Prismo@lemmy.world 6 points 9 months ago

Nice try robots! I’m not helping you learn how to fool us humans.

18
Help with intermittent extrusion issue (imgur.com)
submitted 9 months ago* (last edited 9 months ago) by Prismo@lemmy.world to c/3dprinting@lemmy.ml
16 comments fedilink

Normally slopes on my prints look fine, but recently I’ve been getting bad extrusion on some prints but not all. Same materials, same print file. Could this be one of the motors starting to fail? Printed on an ender 3.

Edit: so changing the POM wheels did nothing. However, I did notice while printing the layers weren’t cooling as much as they should before the next layer started. So maybe there could be a fan issue.

91
This guy is my best friend. Dylan. (imgur.com)
submitted 10 months ago by Prismo@lemmy.world to c/cat@lemmy.world
6 comments fedilink
What websites do you use as an alternative to Amazon? by Prismo in c/asklemmy@lemmy.world
[-] Prismo@lemmy.world 12 points 11 months ago

My small shopify business thanks you!

view more: next ›

Prismo

joined 1 year ago