pepsison52895

I don't remember the first song I played, but I remember blasting Eminem's "Without Me" at full volume with my new 12-inch subwoofer from Walmart. An officer pulled up next to me and my teenage self just about shit a brick. He just started nodding to the beat and drove off.

Microsoft purchased Blizzard.

Beautiful bike. I've got a '14 STR in white and red and I love it. I don't think I'll ever sell it.

Why terrifying?

My spouse and I rode our motorcycles from the Midwest to the East Coast over Thursday and Friday. We've spent the weekend hanging out with family and friends that we haven't seen in months. It's been a good time and we'll be here for the rest of the week.

Interesting. I'm not seeing my instance in there at all.

How can you check to see if your instance is federated with them?

I like to drink Body Armor when I'm cycling or riding my motorcycle on a hot day.

I actually do customer support for a faxing service. You'd be amazed how widely used it is still.

The mesh ends up being pretty similar every time, showing that the right side of the bed is lower than the left. The concern is that, when printing after auto leveling, the nozzle is far too close on the right side, causing first layer issues, but all is well on the left. It's almost like the printer believes that the nozzle is further from the bed than it actually is, but only on one side.

I found that the bolts holding the gantry to the base had come loose slightly, and tightened them. That seemed to help a bit, but the issue is still there. I was going to try leveling the x gantry, but I'm still trying to figure out how to do so.

I did some research and was able to pull the mesh. I put it into a visualizer and found that the right side is definitely incorrect (as it matches with the "too low" behavior that I'm seeing. I tried to copy the image here, but Sync won't let me, but here's the values.

 0        1        2        3        4        5        6        7        8        9       10       11       12
 0 +0.03500 -0.02855 -0.09156 -0.15566 -0.22250 -0.29867 -0.38125 -0.45758 -0.51500 -0.54590 -0.55844 -0.56363 -0.57250
 1 +0.01869 -0.01856 -0.05355 -0.09305 -0.14383 -0.21602 -0.30324 -0.38746 -0.45064 -0.48415 -0.49888 -0.50610 -0.51707
 2 +0.00234 -0.00695 -0.01215 -0.02553 -0.05938 -0.12765 -0.22023 -0.31329 -0.38297 -0.41951 -0.43676 -0.44629 -0.45969
 3 -0.01393 +0.00144 +0.02248 +0.03217 +0.01352 -0.05072 -0.14723 -0.24723 -0.32193 -0.36066 -0.37977 -0.39103 -0.40621
 4 -0.03000 +0.00178 +0.04016 +0.06533 +0.05750 -0.00240 -0.09922 -0.20143 -0.27750 -0.31633 -0.33563 -0.34711 -0.36250
 5 -0.04428 -0.00747 +0.03596 +0.06615 +0.06324 +0.00837 -0.08337 -0.18082 -0.25285 -0.28864 -0.30564 -0.31512 -0.32836
 6 -0.05734 -0.02364 +0.01604 +0.04376 +0.04156 -0.00781 -0.09062 -0.17835 -0.24250 -0.27303 -0.28596 -0.29184 -0.30125
 7 -0.07236 -0.04528 -0.01310 +0.00888 +0.00535 -0.03877 -0.11166 -0.18823 -0.24340 -0.26810 -0.27650 -0.27838 -0.28352
 8 -0.09250 -0.07094 -0.04500 -0.02781 -0.03250 -0.07238 -0.13719 -0.20465 -0.25250 -0.27246 -0.27719 -0.27582 -0.27750
 9 -0.11980 -0.10205 -0.08041 -0.06654 -0.07207 -0.10913 -0.16849 -0.22982 -0.27275 -0.28955 -0.29183 -0.28831 -0.28770
10 -0.15219 -0.13878 -0.12196 -0.11197 -0.11906 -0.15424 -0.20929 -0.26559 -0.30453 -0.31884 -0.31920 -0.31399 -0.31156
11 -0.18660 -0.17777 -0.16597 -0.16010 -0.16902 -0.20270 -0.25387 -0.30559 -0.34092 -0.35300 -0.35165 -0.34493 -0.34090
12 -0.22000 -0.21563 -0.20875 -0.20688 -0.21750 -0.24949 -0.29656 -0.34348 -0.37500 -0.38473 -0.38156 -0.37324 -0.36750

The bed leveling is done with the bed and nozzle preheated to printing temp. As for the probe, it's the stock probe on the Ender 3 Max Neo.

The interesting part is the heat soak. I typically heat it and then only wait a minute or two. I'll let it sit for a while and try again.