Fun fact: Torx screwdrivers are compatible with Torx Plus screws, but Trox Plus screwdrivers are only compatible with Torx screws that are one size larger

you are viewing a single comment's thread
view the rest of the comments

[–] Maalus@lemmy.world 17 points 4 months ago (3 children)

Torx doesn't get fucked though, compared to alan or philips

[–] Somethingcheezie@lemmy.world 7 points 4 months ago (4 children)

What about square drive… where does it fit in

[–] Silic0n_Alph4@lemmy.world 17 points 4 months ago

That’s right, it goes in the square hole.

[–] DrBob@lemmy.ca 14 points 4 months ago (1 children)

Robertson! Say his name!

[–] Somethingcheezie@lemmy.world 1 points 4 months ago (1 children)

I was saying it in Mercian for our southern neighbours

[–] Maalus@lemmy.world 3 points 4 months ago

I'm not american so you wasted it anyways

[–] spicytuna62@lemmy.world 8 points 4 months ago (1 children)

Fun fact: There are plenty of times a screw that looks like a Philips head is also compatible with a square drive. I've mostly seen this on electrical outlets and Ikea furniture.

I don't know why Robertson/square drives aren't more common. They're stable and they resist stripping and rounding.

[–] FrederikNJS@lemm.ee 1 points 4 months ago

You mean Pozidriv?

[–] iAvicenna@lemmy.world 3 points 4 months ago (2 children)

wait really? I would imagine those small corners would easily get flattened compared to something with deeper ridges like philips

[–] SparrowRanjitScaur@lemmy.world 3 points 4 months ago* (last edited 4 months ago) (1 children)

Phillips strips way, way easier than Torx. Stripping generally happens when a screwdriver cams out, or pops out of the screw. Here are some excerpts from Wikipedia of Torx vs Phillips.

The hexalobular socket screw drive, often referred to by the original proprietary brand name Torx ( /ˈtɔːrks/) or by the alternative generic name star drive, uses a star-shaped recess in the fastener with six rounded points. It was designed to permit increased torque transfer from the driver to the bit compared to other drive systems. The drive was developed in 1967[44] by Camcar Textron.[45] Torx is very popular in the automotive and electronics industries because of resistance to cam out, and extended bit life, as well as reduced operator fatigue by minimizing the need to bear down on the drive tool to prevent cam out.

And Philips on the other hand:

The Phillips screwdriver design has a tendency to cam out during operation due to angled contact surfaces which create an axial force pushing the driver out of the recess as torque is applied. Despite popular belief,[2] there is no clear evidence that this was a deliberate design feature. When the original patent application was filed in 1933, the inventors described the key objectives as providing a screw head recess that (a) may be produced by a simple punching operation and which (b) is adapted for firm engagement with a driving tool with "no tendency of the driver to cam out".

I'm not sure about Allen. It doesn't cam out very much, but it does still strip a lot easier than Torx. Probably due to the smaller contact points.

[–] hydrospanner@lemmy.world 3 points 4 months ago

Well said.

And with the hex/Allen, it's the small contact points as well as the smaller volume of material that needs to be deformed or removed before slippage can occur, as well as the angle of force on the contact point.

With a hex, the contact point and direction are such that the tool is effectively trying to scrape off material at an angle, and if/when it succeeds even a little bit, it's now much more prone to fail.

With a Torx, the contact area might still be small, but it's being applied to the lobe in a more perpendicular direction, so rather than a scraping failure, it's more of a force that is pushing directly against steel instead of scraping. Not that it can't fail, but the route to failure is significantly less likely.

[–] Maalus@lemmy.world 1 points 4 months ago

Yeah, it was made with torque in mind (like, it's in the name lol). For smaller screws using an impact, you can expect to break the screw before you strip the torx on top. And by smaller I don't mean tiny, more like M4, M5

[–] uis@lemm.ee -2 points 4 months ago

Maybe because different material? Obviously CrV steel won't get fucked like chinesium, no matter the shape.